Rennsteig

Die-set for PEW12 or Ergocrimp
2,5mm², 4,0mm² and 6,0mm²

Die-set for PEW12 or Ergocrimp
4.0mm²,6.0mm² and 10.0mm²
for Basic System Tool PEW12

Die-set for PEW12 or Ergocrimp
4,0mm² and 6,0mm²

Die-set for PEW12 or Ergocrimp
use for SolarLok / HVT contacts1,5mm² + 2,5mm² + 4,0mm² + 6,0mm²

Die-set for PEW12 or Ergocrimp
for 2,5mm² + 4,0mm² + 6,0mm²

Die-set for PEW12 or Ergocrimp
for 4.0mm² 6.0 and 10.0mm² contacts

• For measuring crimp height and width
  
• Special measuring surfaces prevent errors
  
• Reading accuracy 0.01 mm/0.0005“
  
• Range 0-150mm (0-6 inch)
  
• also suitable for standard measurement taskst
  
• large digital display
  
• switchable between mm and inch
  
• Supplied in plastic case
  

for Standard Power Timer Contacts single wire system
Crimpnests 0,5-1,0 mm², 1,5mm², 1,0 - 2,5 mm² and 3,0 - 4,0 mm²

- Self-adjusts to the desired ferrule size
- Ferrule insertion on the side of the tool
- 4 serrated crimping profiles
- Ferrule insertion on the side of the tool

Crimping Tool with Standard ident in plastic case (without locator)

• suitable for crimping turned pin and socket contacts (e.g. HTS, Harting, Ilme...)
• Conductor cross-section area 0,14 - 6,0 mm²
• Indents ajustable in 0,01 mm increments, digital reading
• Calibration by means of supplied go - no go gauge
• RESET function for recalibration
• Reliable crimping with force lock and synchronous crimp jaw movement
• Multifunctional digital display, with settings shown in mm, inches or MIL selector positions
• Mapping Locator position to Crimp spine position via the enclosed matrix

new Rennsteig article No.: 8753 0401 61

Four-indent crimping tool with standard locator in plastic case

• use for crimping of turned male and female contacts (e.g.. HTS, Harting, Ilme...)
• Wire range 0,14 - 6,0 mm²
• Crimp dimensions adjustable in 0,01 mm increments
• Calibration by means of enclosed go - no go gauge
• Forced locking system and synchronous drive of indenters for high reliable crimp connections
• Manufacturer: Rennsteig Werkzeuge

for Solar couplers Multi-Contact Type 4
inkl. Die-set
2,5mm², 4,0mm² and 6,0mm²

for 1,5mm² + 2,5mm² + 4,0mm² + 6,0mm²
inkl. Die-set
inkl. Locator

for the following contacts:

• Tyco SolarLok
• HTS HA/HE
• HTS HN.D
• HTS HVT
• Harting HAN A/E
• Harting HAN D

for 4,0mm², 6,0mm² and 10,0mm²
incl. Die
incl. Locator
4,0mm² 6,0 and 10,0mm²

Crimping tool with quick-change system

• Crimping tool for rapid exchange of different crimping dies
• external 5-piece magazine with practical belt clip for safe and clean storage of crimping dies
• Suitable for crimping insulated and non-insulated connectors and cable lugs or wire end ferrules
• easy tool-free exchange of Dies
• Dies are self-locking, no screws required - simply click into place - done
• low hand force through optimal leverage ratios
• Unlockable force lock for reliable, solder-free electrical crimp connections
• high operating comfort thanks to ergonomically designed two-component grips

interchangeable blades for different cable diameters, Conductor cross section 1,5 - 6,0 mm²

interchangeable blades for different cable diameters, Conductor cross section 4,0 - 10,0 mm²;
Rennsteig No.: 708 269 3

interchangeable blades for different cable diameters,
Conductor cross section 6,0 - 16,0 mm²
Rennsteig No.: 708 233 3

Interchangeable spare blade pair for Rennsteig 707 020

Optional supplement for better management of contacts during the crimping